© R. Mark Sink (Completed bench) |
When it comes to wood benches to build, here is one that is extremely simple and functional. It is the same workbench plan I have used for years but this one is improved in a way where you can build it easier.
Dimension: 14 1/4 Inches Wide (3 1/2" X 4 plus spacing) X 23 7/8 Inches Long X 24 Inches Tall (Note: If boards are only 3 1/4 inches wide, adjust overall width to 13 1/4 inches wide and adjust horizontal cuts.)
This is a really fun project and you can make the cuts with a jigsaw, but a circular saw or electric miter saw is recommended. All your cuts are square cuts except for the bottom of the legs which are simple cuts to make. I use screws so a battery powered drill makes this project a real breeze. You can also nail this bench using #6 finish nails or box nails. You need to pre-drill the holes if possible.
This project takes four 1X4 pine 8' long or 32 feet. You'll need some 1 1/4 inch coarse thread drywall screws. One small box is enough. Glue is recommended to ensure the workbench doesn't loosen up over many years of use.
Step 1: Here's Your Cut Sheet
© R. Mark Sink (Step 2, two sections) |
Legs: 4 @ 23 1/4 inches long
Horizontals: 4 @ 22 1/4 inches long
Horizontals (ends): 4 @ 12 3/4 inches long
(shown in photo right attached to the two legs using a framing square)
Top: 4 @ 23 7/8 inches long
This will leave 48 inches of stock incase you need to re-cut a piece you cut the wrong length. One tool you really need is a framing square. This makes your job simple and critical to ensure your workbench is square itself. The horizontals are glued to the legs and 1 1/4 inch screws are used. Each end horizontal is held back from the edge 3/4 inches. I use a drill bit that has a beveled collar but it's not necessary. Drill a pilot hole 3/4 way into your material. Only drill the piece laying on top or your screws may not hold well.
I attach the top longer horizontal piece with the workbench laying on its top. I place two screws into the horizontal piece directly into the adjacent horizontal end piece. I also place one screw through the leg from the end into the long horizontal piece in the middle of the board.
© R. Mark Sink (Step 3, begin building standing structure) |
When you lay your top pieces on, the ends may not line up perfectly across the narrow end. This is ok. You can draw a straight line and trim it slightly. The lengths of the tops pieces should be slightly longer than the outside length measurement of your existing bench you just constructed.
© R. Mark Sink (Two pieces make handle) |
© R. Mark Sink (Install 4 top pieces) |
This design allows for you to lay your 4 top pieces and the spacing between each piece will allow you to install them without worrying about the 4 pieces being too wide. Mark your screw line 1 1/8 inches back from the edge and insert two screws in each board at the end. Keep all your screws about 3/8 inches from edge of the board.
Your horizontal ends required you to drill your pilot hole 3/8 inches from the end of the board also. This centers your screw into the 3/4 inch material you are screwing into.
© R. Mark Sink (Handle layout) |
Make your handle at least 4 inches long from long point measurement.
I add a lower shelf in my workbench to throw stuff while I'm working with the bench. You only need for smaller pieces of scrap to nail or screw in the inside lower banding.
© R. Mark Sink (Lower inside shelf) |
Surprisingly, these workbenches last forever if you keep them dry. If you leave them outside, they can rot out in just a year or two. Store your workbench out of the rain! This is critical to its life.
Copyright 2005© Randy Sink
Revised 2012
No comments:
Post a Comment